Abstract
Mn-doped tetrahedrites Cu_12-xMn_xSb₄S₁₃ (0.1 ≤ x ≤ 0.4) were synthesized by mechanical alloying (MA) and sintered by hot pressing (HP). A single tetrahedrite phase was synthesized by MA without post-annealing, and it was stable without any phase changes after HP. The hot-pressed specimens had a relative density higher than 98.6%...... More

Abstract
Inkjet printing is a very attractive technology for printed electronics and a potential alternative to current high cost and multi-chemical lithography processes, for display and other applications in the electronics field. Inkjet technology can be employed to fabricate organic light emitting diodes (OLED), quantum dots displays, and thin-film transistors (TFTs)...... More

Abstract
In this study, we studied the surface and mechanical properties of multiple additives as well as the initial plating properties of individual additives. With the individual additive groups, copper crystals tended to converge at a stage above the critical amount of additive. When chloride ions were added, large crystals formed..... More

Abstract
The powder microstructure and sintering behavior of W prepared by ultrasonic spray pyrolysis and spark plasma sintering were investigated. Fine-grained W powders were synthesized by ultrasonic spray pyrolysis using an ammonium metatungstate hydrate solution and hydrogen reduction. The XRD analysis of the powder, pyrolyzed below 600 ^oC, showed tungsten oxide..... More

Abstract
We grew ZnO nanorods (NRs) using a hydrothermal method while rotating the precursor solution, and report the effect of rotation on surface modification, and the optical and ultraviolet (UV) photoresponse properties of the resulting ZnO nanorods. The ZnO NRs grown in the rotating precursor solution at 100 rpm had the..... More

Abstract
Nanocrystalline Fe-Si-B-Nb-Cu Finemet alloys show low saturation magnetic flux density compared to amorphous Fe-Si-B alloys. In the Fe-Si-B-Cu base amorphous alloys, Cu atoms form clusters which act as heterogeneous nucleation sites for α-Fe crystals. The addition of Ca element atoms, distributed along grain boundaries, helps inhibit grain growth and increase..... More

Abstract
Solution-processed zinc tin oxide (ZTO) thin-film transistors (TFTs) have great potential uses in next-generation wearable and flexible electronic products. Zinc and tin precursor materials are naturally abundant and have low fabrication costs. To integrate a single ZTO TFT into logic circuits including inverters, NAND, and NOR gates will require the..... More

Abstract
When an elastomeric photomask is used for near-field contact printing, the high deformability of the elastomer mask plate enables gap-free full contact with the substrate, minimizing the effect of diffraction. This image-transfer technique provides sub-50 nm resolution and depth-of-focus-free lithographic capability with cost-efficient equipment. However, the method’s application is limited..... More

Abstract
The formation of porous material structures has been widely investigated for the development of high-performance energy materials, catalysts, and chemical sensing devices. Various nanoporous structure fabrication methods are based on wet-chemical processes, which require precise control of the process parameters. Physical vapor deposition such as thermal evaporation utilizes high vacuum..... More

Abstract
Ti has excellent properties but is more expensive than other materials due to its high melting point, high reactivity and difficult processability. One way to lower the production cost of Ti products is to recycle Ti scraps. Before recycling Ti scraps, pretreatment to remove contamination is essential. Ti scraps can..... More

Abstract
The Charpy impact test is used to identify the transition between ductility and brittleness. The percentages of ductile and brittle fractures in steel can be evaluated based on each fracture area, which is presently determined by an analyzer with the naked eye. This method may lead to subjective judgement, and..... More

Abstract
In ironmaking, the optimal size of the iron ore charged into a blast furnace is generally 10-30 mm. Oversized ores, which have a smaller reaction surface area, are crushed, while undersized ores, which decrease permeability, undergo a sizing process before being charged into the blast furnace. Recently, however, iron ore..... More

Abstract
Solar water splitting is an attractive method for producing hydrogen from renewable natural resources, and heterostructure photocatalysts have been widely investigated for photocatalytic applications. Hetero-component photocatalysts can reduce the charge recombination process by improving electron utilization, and are considered promising candidates for solar water splitting. Amongst various heterostructure systems, combinations..... More

Abstract
Nickel hexacyanoferrate (NiHCF) has a three-dimensional open framework structure, excellent long-cycling stability and rate performance as a cathode for aqueous sodium-ion batteries. However, the specific capacity of NiHCF is lower than that of present cathodes for aqueous batteries. A sodium-ion electrolyte was explored to achieve optimum capacity with NiHCF. Powder-type..... More

Abstract
In this study, oxide (Y₂O₃)-embedded Ni particles were fabricated via a new process. The process involves the mechanical hydrogenation of Ni–Y alloy into Ni–YH₂ and the selective oxidation of Ni–YH₂ to Ni–Y₂O₃. The alloy powders were prepared for sintering by the mechanical alloying of a mixed powder. The powder was..... More

Abstract
The effects of the cooling rate, after solution heat treatment, on the microstructures and mechanical properties of Fe-22Mn-8Al-0.8C-0.02Nb (low carbon) and Fe-20Mn-8Al-1.1C-0.1Nb (high carbon) light-weight steels were systematically investigated. The cooling process was controlled to achieve six different cooling rates, ranging from -0.016 to -465.1 ^oC/s. Under the slowest cooling..... More

Abstract
To automatically reconstruct the prior austenite grains from as-quenched martensitic structure, we applied a deep learning algorithm to recognize the prior austenite grains boundaries hidden in the martensitic matrix. The FC-DenseNet architecture based on FCN (fully convolutional networks) was used to train the martensite and ground truth label of the..... More

Abstract
ZrO₂ is a promising candidate for knee and hip joint replacements due to its excellent combination of low density, corrosion resistance and biocompatibility. Nevertheless, a low fracture toughness of pure ZrO₂ at room temperature limits its wider application in the industry. One of the most obvious ways to solve the..... More

Abstract
Recent large-scale fires in buildings and logistic warehouses have become a major social issue, involving both property loss and multiple casualties. To make color coated steel sheets non-combustible and/or have anti-fire properties, various ways of optimizing manufacturing parameters have been investigated for outer, inner, roof and ceiling panels. In the..... More

Abstract
In this study, high-strength pure Cu bulk material was manufactured using a cold spray additive manufacturing process, and its microstructure, tensile and compressive deformation behaviors were investigated and compared. The cold spray additive manufactured Cu bulk material showed a heterogeneous grain structure consisting of fine-grains and coarse-grains, and only α..... More

Abstract
The effect of pre-strain on the hydrogen embrittlement of Nb-free and Nb-added low-carbon steels with ferrite-pearlite structure was investigated in this study. After the steels were electrochemically charged with hydrogen, slow-strain rate tensile (SSRT) tests were conducted on them to examine hydrogen embrittlement behavior. The SSRT test results revealed that..... More

Abstract
Al-Mg-Si alloy was rolled asymmetrically at several temperatures to apply shear deformation, and the effects of the initial precipitate on shear deformation, texture evolution, formability, and plastic anisotropy were studied. Texture was analyzed using a EBSD, and the formability and plastic anisotropy of the specimen were evaluated using the value..... More

Abstract
Fe-Mn-Si based shape memory alloy is a new functional material that can be used to apply prestress to civil and structural components such as concrete structures. In this study, the effects of alloying elements Ni, C and Ti on the mechanical and shape memory properties of the alloy were investigated..... More

Abstract
To clearly understand the effect of the eutectic structure in the Zn-Al-Mg alloy coating on the corrosion behaviors in chloride containing aqueous environments, a bulk Zn-MgZn₂ sample was fabricated by diffusion bonding process, and a variety of experiments, such as electrochemical polarization and galvanic corrosion measurements, salt spray tests, and..... More

Abstract
In this study, consolidated WC-Fe compacts as a function of Fe contents were fabricated by a spark plasma sintering method, following the mixed by the ball-milled powder. Fe among the metallic binders was added to WC enhance not only the driving force of sintering process but also suppressing the grain..... More

Abstract
The small punch (SP) test is one of the small specimen test techniques, and standardization of the SP test method for evaluating the mechanical properties of metallic materials is in progress. In this study, the impact transition temperature of reactor pressure vessel steels (RPV) in nuclear power plants was estimated..... More

Abstract
This study examined the effect of alkalis on lyocell-based activated carbon fibres (ACFs) with high Brunauer-Emmett-Teller (BET) surface areas, using X-ray diffraction (XRD). Here, alkali treatments were conducted using 10 ~ 25 % NaOH and KOH on lyocell samples for 3 h at ambient room temperature. A secondary treatment with..... More

Abstract
Cu-Ni-Si alloys were strengthened by Ni₂Si intermetallic compound precipitation in a Cu matrix during aging. The Cu-6 wt% Ni-1.4wt%Si alloy was prepared by water quenching (solution treatment) or air cooling (homogenization treatment) after heating 980 ^oC for 2 hours and aging at 500 ^oC for 6 hours. After maintaining a..... More

Abstract
Polycrystalline diamond compact (PDC) has excellent wear resistance, high impact resistance, superior fatigue properties, and has been used in the oil and gas drilling industries. This study investigated the effect of Co leaching on the microstructure, vertical turning lathe (VTL) wear properties of PDCs manufactured by high-temperature and high-pressure (HTHP)..... More

Abstract
The subject of this study was a bronze sword excavated from the early Iron Age area of Sinpung site in Wanju. SEM-EDS, FE-EPMA and Raman Micro-Spectroscopy analysis methods were applied to investigate the manufacturing techniques and corrosion characteristics. The results of the analysis indicated a casting structure composed of both..... More